Friday, August 29, 2008

Test Ride #3_Coconino Rally

We went out fairly late yesterday, KLR and I.
T'was good.

Rode "The Triangle" and covered it in 51 minutes or so.
Next on the list of objectives was to time "FS700 to The Park" but actually ran out of daylight at the last moment. I suspect that it will take about 45 minutes moving along quite comfortably (not even close to riding short of like a madman.)

We changed course as the sun set and ultimately reached Lake Mary road in the darkness.
It is down right spooky cruizing the back roads at dusk knowing that the Elk are get close to their mating season. The are all over the place!

The late start was due to mounting some ProTaper Contour handlebars and grips to the ol' girl.
Also got sidetracked mapping out the wiring plans for the new fuse boxes I received that day.
Check it!

















Above left: 6-Slot and 4-Slot fuse panels from Centech. Each slot rated to 30amps.
Above Right: The Fuse panel that will be replaced. It worked out just fine with no problems. I just have other plans for the spot it currently occupies. Below Left: The planned location for the new Fuse Boxes.





















Above Right: The replacement bars for my sorry-bent-steel-stock bars...but hey, they got the job done no problem. Below: Better view of the ProTaper ATV Contour handlebars. They are the CR High model, mounted on RoxRisers from RoxSpeedFX.com.


There is something you should know if you are interested in this bar or any O/S bar as a replacement:
  1. This model is not as high as stock
  2. The CR High model is not as wide as stock
  3. If you use a Brush Guard, take note that the clamping-mount will require a larger diameter fitting to work with an O/S bar. I use the Acerbis RallyPro guards and now need to order the appropriate clamp size.

Because the bar is not as wide, I will have to seek out adaptors for my HID bar lamps. There are a few cool products in the bicycle industry that may work out nicely. Let me add however, that I do like this width a lot better...I am a small guy at 130lbs after all.

I low-sided yesterday while trying to drift a sandy turn--landed right on my chest, too. I am so glad about that EVS body armour. Didn't even get the wind knocked out of me. I am aware of the state of my fortune yet again (Mustn't forget that balance between confidence and cockiness, less my fortune run out.) Anyway, it was luck the clutch lever didn't snap on impact. Gotta get those guards back on!

Well, out for another test ride. It is all shaping up desirably now and on-schedule. Objectives for today are to get the coordinates for GC21 @ The Park, recon a Bonus GC at Walnut Canyon, recon the new main route through Cinder Hills OHV. Oh, and get the coordintes for two other bonus GC locations. Big day, gotta go!

As my very good friend Dave See would say:

Ride One Long

Tuesday, August 26, 2008

Geocache Test Ride Part 2

10 hours for 170 miles of dirt...


That's forest road, 2 track and even a little bit of single.

Rock gardens galore and loose sand (or rathercinder) at the Cinder Hills.


Shortened significantly from Test Ride #1.


It's still too long and the navigation may be too difficult for a Rally.


T'was fun, though. T'was fun.
It kinda got scary too: The Elk are mating and are just all over the place right now, madness!


Tomorrow I will be doing Test Ride #3. The objective is to get it under 6 hours which will require cutting out the East Pocket section all togother.


Next year, the format will include the Rally spent over two days instead of one.


After tomorrows test ride I will begin to place all the Geocaches.


Also...got in some new goodies...

Tuesday, July 15, 2008

SGTMarty makes it to Silverton, CO on time!



Like many KLR and adventure riders all over, I have been following the epic journey of one SGTMarty, a recently retired Aurora Police officer who is ranging the length of Prudhoe Bay, Alaska to the tip of South America on his KLR.


There are many such adventures to read along on the

world-wide-web, but SGTMarty's is just a little bit

different. There is something about his writing style and the personality that he brings to the table that captivates his audience. I like many find myself longing for the road, inspired by his antics and literary technique.



Horizon's Unlimited is hosting this years southwest gathering in Silverton, CO, and many doubted this fanatic would make his
goal of attending the meeting...


well, he made it.


SGTMarty has run out of fuel in the middle of the Yukon,
later to be saved by a pack of Harley Davidson rufians, has taken a fridged dunk in the waters of Prudhoe Bay,
braved soft gravel Alaskan roads on an overladen moto,
rode hundreds of miles on dangerously worn sprockets,
and dodged head on collisions with moose and buffalo.

And he's still only in North America!

I find myself dreaming of the day when I leave for Mexico on my own scoot, ready for the open road and whatever life presents me with.





If you too long for adventure...Check out his report here.




All photos are SGTMarty's own from his coverage of this on going adventure of a lifetime.

Monday, June 30, 2008

Doin' the Doo


...and No, I don't mean the x-games cool-guy drink.

I'm talking about the infamous idler shaft lever chain adjuster thingymerbob-or aka the "doohickey"

Kawasaki part No. 13168



This little piece (o' metal) is known to selfdestruct or rather justsnap from regular wear and tear.
No, it's not supposed to be that way, the stocker is just poorly manufactured.
If and when it breaks, metal parts hopefully find its way in the oily mess of the engine internals and not into any of the stuff that will cause very bad things to happen to, well, your engine.

So, as preventive maintainence, I, like many KLRistas, have decided to replace the stocker with this fine finely made alternative by Eagle Manufacturing & Engineering.






I sourced mine from TPI Motorcycle Parts which I recieved today.

Do I know what I'm doing? Yes and No.

Here are some excellent How-To Articles of the web:

KLRWorld.com forums Marty

KLRWorld.com forums KeithM
and
MarkNet - KLR650


Along with doing the Doo I am also knee deep in KLR shii...uh maintainence.

Here's the list so far:

- Doooohickey

-Oil and Filter change

- Flat Magnetic Oil plug

- Valve Clearance

- Clean and oil airfilter

- Radiator flush

- Percival mod (PCV)

- Tool tube vision...(you'll see)

- change rear tire to Dunlop D606

- Relocate Auxilary Gas rack and increase to
2 1/2 gal total back-up fuel.


- Sew up a fender tool bag (DYI)

- Install 1" riser links to swing arm

- install new KTM front fender

- Kevlar front brake pads

- Relocate foot peg brackets


- install offroad footpegs


- AND! the Fairing MOdeyssey Part II- The Saga Continues


Yes it's a lot of stuff. It's not all here it either...but in route none the less.

Here are some great How-To articles for the Valve Clearance:

KLRWorld.com Forums by The Patman

and

MarkNet - KLR650 Valve Adjustment

Time to have some fun.

Saturday, June 14, 2008

Fairing KLR650 Fairing KLR 650



Web searches boggle me...so this post is an experiment for the "google searching" needs.

-V